Skip to content

Industries Served

Aerospace and defense. That is the whole list.

A shop that also runs automotive work is optimized for a different problem. Ours is configured for programs measured in decades — where configuration control, traceability, and a supplier who is still there in year eight matter as much as the price per piece.

01

Aerostructures

Monolithic machined detail that has to be interchangeable across a whole airframe build rate.

Typical materials
7075-T651, 7050-T7451, 15-5PH, Ti-6Al-4V
Annual volume band
2,000 – 100,000 pcs / yr

Representative part families

  • Machined brackets and clips
  • Fittings and lugs
  • Ribs and intercostals
  • Seat-track hardware
  • Door and latch mechanisms
02

Engines & Propulsion

Hot-section and rotating hardware where material behavior, not the machine, sets the cycle.

Typical materials
Inconel 718, Waspaloy, A286, Haynes 282
Annual volume band
500 – 25,000 pcs / yr

Representative part families

  • Bearing housings
  • Fuel and lube manifolds
  • Seal rings and carriers
  • Blisk and impeller work
  • Case fittings and bosses
03

Defense Systems

Ground, naval, and munitions hardware under ITAR control, built to sustained rate with full traceability.

Typical materials
4340, 300M, 17-4PH, 6061-T6, tungsten alloy
Annual volume band
1,000 – 250,000 pcs / yr

Representative part families

  • Guidance and seeker housings
  • Ordnance components
  • Actuator bodies
  • Optics and sensor mounts
  • Weapon-station hardware
04

Fluid & Actuation

Sealing-surface and bore work where finish and roundness decide whether the assembly leaks.

Typical materials
15-5PH, 17-4PH, 4140, C17200, Nitronic 60
Annual volume band
5,000 – 150,000 pcs / yr

Representative part families

  • Valve bodies and spools
  • Actuator pistons and rods
  • Hydraulic fittings
  • Pump housings
  • Accumulator components
05

Space & Launch

Low-rate, high-consequence hardware — and the sudden ramp when a program finds its cadence.

Typical materials
6061-T6, 2219, Inconel 625, Ti-6Al-4V ELI, C110
Annual volume band
100 – 10,000 pcs / yr

Representative part families

  • Thruster and injector bodies
  • Structural interfaces
  • Cryogenic valve components
  • Payload mounts
  • Feedline hardware
06

Unmanned & Autonomy

Programs that need prototype speed first and a 10× rate increase eighteen months later, without changing suppliers.

Typical materials
7075-T651, 6061-T6, Ti-6Al-4V, PEEK
Annual volume band
1,000 – 200,000 pcs / yr

Representative part families

  • Airframe and gimbal structure
  • Payload housings
  • Drive and gearbox components
  • Launch and recovery hardware

Program Support

What a defense program actually needs from a machine shop.

Price per piece is the easy part of the conversation. These are the things that decide whether a supplier survives an audit and a rate increase.

ITAR-controlled work

DDTC registered, with segregated storage, access-controlled technical data, and US persons only on controlled programs.

Long-term agreements

Blanket POs, LTAs, and kanban releases with pricing held across the term and capacity reserved against the forecast.

Source & government inspection

Set up to host customer source inspection and DCMA involvement, with government property management procedures in place.

Obsolescence & re-sourcing

Reverse engineering from legacy 2D prints and sample hardware when the original supplier or model is gone.

Configuration control

Revision-controlled programs, tooling, and routers. The part built in year six matches the part built in year one.

Surge capacity

Reserved spindle hours and retained tooling so a rate increase does not restart the qualification clock.

Request for Quote

Requalifying a part you would rather not requalify?

Send the print and the history. We have taken over enough orphaned part numbers to know what usually went wrong the first time.

Start an RFQ(937) 555-0140

AS9100D · ITAR Registered · CMMC Level 2 · CAGE 0ABC1